Request a quote for HJ2600(W) →
| Model | HJ2600(W) |
|---|---|
| Series | HJ (W) |
| Type | HJ series vulcanized clamping device (XZL) |
| Clamping range | 130-160 mm |
| Clamping force | 150 kN |
| B | 200(6-M8) |
| I | 179-280 mm |
| E | 121 mm |
| H1 | 56 mm |
| Thread S | M30*1.5 |
| Max speed | 3,500 rpm |
| Run-out | ≤ 0.01 mm |
| Hardness | HRC 58-62 (bulk carburized, quenched, cryogenic treated) |
| Spindle connection | Flange matched to your spindle nose — specify machine at RFQ |
| Brand | Mongtec Precision Inc. — Taiwanese brand, designed and engineered in Taichung, Taiwan |
Source: Mongtec Quick Change Collet Chucks catalogue, Ver 2026.
HJ2600(W) expands inside a bore and clamps the part from the inside. The clamping element is a segmented rubber-vulcanized module: the segments are ground as one piece and then split, so every segment seats fully on the workpiece instead of contacting on three points. That is what holds run-out at ≤ 0.01 mm while still accepting ±0.5 mm of part-to-part variation.
The wide acceptance band is the reason this style of fixture suits automatic loading — a bar-fed or robot-loaded part that lands slightly off nominal is still clamped concentrically, where a conventional three-jaw or spring collet would either miss or clamp off-centre.
The clamping module is replaced without taking the fixture off the spindle. Changing the part size means changing the module, not re-setting the fixture — which is where the time is saved on short runs and mixed batches.
| Model | Clamping range | Clamping force | Max speed |
|---|---|---|---|
| HJ2000XXS(W) | 8-13 mm | 42 kN | 6,000 rpm |
| HJ2000XS(W) | 13-19 mm | 42 kN | 6,000 rpm |
| HJ2000X(W) | 16-21 mm | 42 kN | 6,000 rpm |
| HJ2000(W) | 20-28 mm | 42 kN | 6,000 rpm |
| HJ2100(W) | 26-38 mm | 42 kN | 5,000 rpm |
| HJ2200(W) | 36-54 mm | 85 kN | 5,000 rpm |
| HJ2300(W) | 50-80 mm | 105 kN | 5,000 rpm |
| HJ2400(W) | 69-100 mm | 150 kN | 5,000 rpm |
| HJ2500(W) | 100-130 mm | 150 kN | 4,500 rpm |
| HJ2700(W) | 160-192 mm | 150 kN | 3,500 rpm |
HJ2600(W) covers a clamping range of 130-160 mm on the bore. Within that range the clamping module absorbs up to ±0.5 mm of workpiece variation, which is what makes it suitable for automatic loading.
The fixture body is standard; the connection to your machine is made through a flange matched to your spindle nose. Tell Mongtec the machine and spindle nose and the correct flange is quoted with the fixture.
The rubber clamping module is replaced without removing the fixture from the spindle — a matter of seconds rather than a re-setup. Changing to a different clamping range means changing the module, not the fixture.
Send the machine and spindle nose, the part diameter and bore you need to hold, and whether the parts are loaded by hand, bar feed or robot. Dimensioned drawings are supplied by email once the enquiry is open.
All quick-change clamping models · Quick-change clamping overview · All Mongtec article numbers