Mongtec Precision, a Taiwanese tooling brand headquartered in Taichung, Taiwan, designs and engineers driven tool holders and static tooling for the Gildemeister CTX gamma 2000 on the open machine-side BMT and VDI (DIN 69880) standards. This model is published with a VDI40 turret; Mongtec engineering confirms it against the actual turret drawing at RFQ, and every driven unit ships with an individual inspection report.
| Machine brand | Gildemeister |
|---|---|
| Model | CTX gamma 2000 |
| Turret interface | VDI40 (published in a machine-specific tooling catalogue by a driven tool holder manufacturer; confirmed against the actual turret drawing at RFQ) |
| Driven tool holders | Axial, radial, adjustable-angle, twin-output, high-speed and geared-down units |
| Static tooling | Turning, boring bar, facing, cut-off and blank holders |
| Inspection | Individual inspection report with every driven unit |
| Origin | Taiwanese brand headquartered in Taichung, Taiwan |
Gildemeister / DMG turret rule: machines specified as "VDI30 or VDI40" are built with either — both sizes are listed and the fitted size is confirmed from the machine. Trifix VDI turrets accept standard VDI holders.
TOOL HOLDER SELECTION GUIDE Ver 2026.08 (PDF, 2.6 MB)
Mongtec also supplies BMT40, BMT60, BMT68 and BMT80 holders and builder-specific interfaces (Mazak, Nakamura-Tome, Haas BOT, Okuma BOT, Muratec BOT) — the 228 article numbers published here are a subset of the range. Mongtec tooling is exported to five continents and supplied to machine-tool builders. Lead time is confirmed per item and quantity at quotation.
Machine builders routinely offer the same model with more than one turret — station count, model suffix and key count all change the mounting. Hardinge Conquest H51 is BMT55 in the 12-station build and BMT45 in the 16-station build; Okuma GENOS L300 M is VDI40 while L300 MW/MYW uses a 65×73 bolt pattern. It is the most common reason a driven tool holder arrives and will not bolt on. Reference table: 38 BMT turret bolt patterns by machine builder →
Send the machine model and turret photo — we confirm the fit before quoting →
Machine-specific tooling catalogues publish this model with a VDI40 turret. Machine builders do sometimes ship the same model with more than one turret, so Mongtec confirms the interface against the actual turret drawing before quoting. That check is free and takes one email.
The catalogue dimensioned drawing is published on the page of each Mongtec article number. After your enquiry Mongtec confirms compatibility with your actual spindle, turret or pull stud and gives the final article number — that check is free.
Yes. Special angles, extended reach, high-pressure internal coolant and non-standard mountings are supplied to order. Describe the operation and the machine.
A selection of Mongtec VDI40 driven tool holder article numbers. This is a starting point, not a confirmed fit — the exact turret drawing is verified at RFQ. See all 75 VDI40 article numbers →
| Article no. | Orientation | Collet | Max speed | Torque |
|---|---|---|---|---|
| M2926 | Axial | ER32 | 5,000 rpm | 70 Nm |
| M5066 | Axial | ER32 | 6,000 rpm | 40 Nm |
| M9066 | Axial | ER40 | 5,000 rpm | 70 Nm |
| M0166 | Radial | ER32 | 8,000 rpm | 20 Nm |
| M0626 | Radial | ER25 | 8,000 rpm | 20 Nm |
| M4326 | Radial | ER32 | 5,000 rpm | 70 Nm |
All Gildemeister models · Driven tool holder types and turret interfaces · Published article numbers · Static turret tooling · Selection guide
Machine builders regularly ship the same model with different turrets — station count, model suffix and the number of keys all change the mounting. The Hardinge Conquest H51 is BMT55 in the 12-station build and BMT45 in the 16-station build; the Okuma GENOS L300 M is VDI40, while the L300 MW/MYW uses a 65×73 mm bolt pattern. This is the single most common reason a driven tool holder arrives and will not bolt on. BMT bolt pattern reference — 38 patterns by machine builder →
Send your model and a photo of the turret face — we confirm the fit before quoting →
Whether a holder mounts is decided by the turret bolt pattern and the drive coupling, not by the machine name alone. The types below are published by Mongtec for this interface; the exact article number is confirmed against the actual turret drawing at RFQ.
VDI40 article numbers · BMT bolt pattern reference (38 patterns) · All driven tool types and turret interfaces