Mongtec Precision, a Taiwanese tooling brand headquartered in Taichung, Taiwan, designs and engineers driven tool holders and static tooling for the Nakamura-Tome TW-20 (16-station) on the open machine-side BMT and VDI (DIN 69880) standards. The turret interface for this model is confirmed by Mongtec engineering against the actual turret drawing at RFQ, and every driven unit ships with an individual inspection report.
| Machine brand | Nakamura-Tome |
|---|---|
| Model | TW-20 (16-station) |
| Turret interface | Not published for this model yet. Nakamura-Tome turret rule: the BMT44, BMT55 and BMT65 turrets on Nakamura machines are Nakamura-specific designs — standard catalogue BMT holders do not fit them. Mongtec supplies holders to the Nakamura interface and supplies them regularly. Where a Nakamura machine carries a VDI40 turret, standard VDI40 applies. Send the machine model, station count and a turret photo — Mongtec confirms the interface free of charge. |
| Driven tool holders | Axial, radial, adjustable-angle, twin-output, high-speed and geared-down units |
| Static tooling | Turning, boring bar, facing, cut-off and blank holders |
| Inspection | Individual inspection report with every driven unit |
| Origin | Taiwanese brand headquartered in Taichung, Taiwan |
Nakamura-Tome turret rule: the BMT44, BMT55 and BMT65 turrets on Nakamura machines are Nakamura-specific designs — standard catalogue BMT holders do not fit them. Mongtec supplies holders to the Nakamura interface and supplies them regularly. Where a Nakamura machine carries a VDI40 turret, standard VDI40 applies.
TOOL HOLDER SELECTION GUIDE Ver 2026.08 (PDF, 2.6 MB)
Mongtec also supplies BMT40, BMT60, BMT68 and BMT80 holders and builder-specific interfaces (Mazak, Nakamura-Tome, Haas BOT, Okuma BOT, Muratec BOT) — the 228 article numbers published here are a subset of the range. Mongtec tooling is exported to five continents and supplied to machine-tool builders. Lead time is confirmed per item and quantity at quotation.
This catalogue entry is the 16-station build. Station count changes the turret on many machines, so the build must be confirmed before a holder is quoted.
Machine builders routinely ship the same model with more than one turret. These are all published, verified examples:
| Machine | What changes | Turret mounting |
|---|---|---|
| Hardinge Conquest H51 | station count | 12-station = BMT55 · 16-station = BMT45 |
| Okuma GENOS L300 | model suffix | L300 M = VDI40 · L300 MW/MYW = 65×73 bolt pattern |
| DMG MORI ALC / ALX 1500–2500 | turret build | BMT40 or BMT42/64 |
| Takisawa TS-3000 / 4000 | key count | 2-key and 3-key turrets are not interchangeable |
It is the most common reason a driven tool holder arrives and will not bolt on. Reference table: 38 BMT turret bolt patterns by machine builder →
Send the machine model and a photo of the turret face — we confirm the fit before quoting →
We have not published a figure for this model because the public machine specifications do not state it consistently, and a guessed figure is worse than a blank field. Send the machine model and a photograph of the turret face and Mongtec engineering confirms it against the actual turret drawing. That check is free and takes one email.
The catalogue dimensioned drawing is published on the page of each Mongtec article number. After your enquiry Mongtec confirms compatibility with your actual spindle, turret or pull stud and gives the final article number — that check is free.
Yes. Special angles, extended reach, high-pressure internal coolant and non-standard mountings are supplied to order. Describe the operation and the machine.
Yes — Mongtec supplies driven and static tool holders for this turret. This Nakamura turret uses a 60 × 50 mm BMT bolt pattern. It is a different design from the generic BMT45 published as article numbers on this site, so those catalogue article numbers do not apply here and should not be ordered against this machine. Mongtec supplies to the Nakamura pattern regularly.
Turret coverage: Nakamura-Tome WT150, WT250 · WT150II, WT250II · WTW150 · WTS150 · SUPER NTM3 · SUPER NTJ · SUPER NTJX · SC150, SC200, SC250 · NTY3 250 · TW10M / MY / MM / MMY / MMYY · TW20M… (16 ST) · WY250 · AS200 (15, 24 ST).
Mongtec driven and static tool holders are exported worldwide across five continents, and are supplied to machine tool manufacturers as well as to end users. Lead time is confirmed against the items and quantity you need.
To quote we need: the machine model and turret designation, the station count, a turret interface drawing or a clear photo of the turret face, the holder orientation (axial or radial) and the clamping or collet size you need, and the quantity. A drawing of the holder you are replacing works just as well.
Email info@mongtec.com to discuss your application and request drawings, or send an enquiry here. Mongtec engineering confirms the fit against your turret before quoting.
All Nakamura-Tome models · Driven tool holder types and turret interfaces · Published article numbers · Static turret tooling
Machine builders regularly ship the same model with different turrets — station count, model suffix and the number of keys all change the mounting. The Hardinge Conquest H51 is BMT55 in the 12-station build and BMT45 in the 16-station build; the Okuma GENOS L300 M is VDI40, while the L300 MW/MYW uses a 65×73 mm bolt pattern. This is the single most common reason a driven tool holder arrives and will not bolt on. BMT bolt pattern reference — 38 patterns by machine builder →
Send your model and a photo of the turret face — we confirm the fit before quoting →
The turret interface for this machine is confirmed at RFQ, so no article number is published here. These are the driven tool types Mongtec publishes — which one fits is confirmed once the turret is identified.
BMT bolt pattern reference (38 patterns) · All driven tool types and turret interfaces