Axial multi-spindle holders carry several parallel outputs on one station, so a bolt circle or a hole pattern is produced in a single stroke. Mongtec Precision, a Taiwanese tooling brand headquartered in Taichung, Taiwan, supplies them to mount on Victor turrets, published for BMT55, BMT65, BMT75.
Developed specifically for high-efficiency machining on Victor Taichung multitasking centers. Featuring an axial dual-output configuration, this toolholder is designed to double tool capacity within a single station. Combined with the high-rigidity power transmission of Victor turrets, it supports synchronized or sequential machining on both main and sub-spindles, significantly shortening cycle times and maximizing turret space utilization.
26 Victor models. Where the turret interface is published it is shown; where it is blank the interface depends on the turret actually fitted and is confirmed at enquiry.
| Machine model | Turret interface (where published) | Turret |
|---|---|---|
| VTurn II-16/20CV (DIN1809) | — | — |
| VTurn II-16/20CV (DIN5480) | — | — |
| VTurn II-16/20YCV | — | — |
| VTurn II-23/26CV (DIN1809) | — | — |
| VTurn II-23/26CV (DIN5480) | — | — |
| VTurn II-23/26BCV, YCV | — | — |
| VTurn-36CV (DIN5482) | — | — |
| VTurn-36/40/45/46CV (DIN5480) | — | — |
| VTurn-40/45CM (BMT75) | BMT75 | — |
| VTurn-40/45YCM (BMT75) | BMT75 | — |
| VTurn-A16/20CV (DIN5480) | — | — |
| VTurn-A16/20/200CM, SCM, YCM, YSCM | — | — |
| VTurn-A16/20SCV, YCV, YSCV | — | — |
| VTurn-A26CV | — | — |
| VTurn-A260YCM, YSCM (16ST, BMT55) | BMT55 | 16-station |
| VTurn-A26/260SCM, YSCM (12ST, BMT65) | BMT65 | 12-station |
| VTurn-A26SCV, YCV, YSCV | — | — |
| VTurn-NP16CM | — | — |
| VTurn-NP20CM, S20CM | — | — |
| VTurn-Q200T2Y2/T3Y3 | — | — |
| VTurn-S26CM | — | — |
| VTurn-S36CM | — | — |
| VTurn-V560CV | — | — |
| VTurn-V760CV | — | — |
| VTurn-V760CM (BMT75) | BMT75 | — |
| VTurn-V1000 (CM) | — | — |
All machine builders for 0° multi-axis driven toolholders →
The machine model alone does not decide the holder. The same model can leave the factory with different turrets — station count, model suffix and key arrangement all change the mounting. Tell us the machine, the turret and the operation and we confirm the mounting before quoting.
Already using another brand? Send the drawing or the article number of the holder you run today and Mongtec will convert it to an equivalent Mongtec holder — same mounting, same reach, same output.
Mongtec publishes adjustable-angle driven tool holders for 24 Victor machine models, on turret interfaces BMT55, BMT65, BMT75. On these machines the holder is used for drilling and milling at angles between 0° and 90°, for features that sit neither on the face nor square to the diameter. Article numbers are matched to the machine at RFQ — we confirm the turret interface from the builder’s drawing rather than assume it from the model name.
Victor machine not on this list? Send the model and we confirm the interface →