Axial multi-spindle holders carry several parallel outputs on one station, so a bolt circle or a hole pattern is produced in a single stroke. Mongtec Precision, a Taiwanese tooling brand headquartered in Taichung, Taiwan, builds them to mount on Goodway turrets.
Specially designed for Goodway multitasking turning-milling centers, featuring a dual-output spindle configuration aimed at maximizing machining efficiency and shortening cycle times. While maintaining Goodway’s signature high rigidity and powerful torque transmission, these multi-axis toolholders enable multiple operations or simultaneous front-and-back machining in a single setup, providing the optimal solution for boosting productivity and Overall Equipment Effectiveness (OEE).
35 Goodway models. Where the turret interface is published it is shown; where it is blank the interface depends on the turret actually fitted and is confirmed at enquiry.
| Machine model | Turret interface (where published) | Turret |
|---|---|---|
| GA-2000-3600 M | — | — |
| GA-3000, 3300, 3600 | — | — |
| GLA-1500 M | — | — |
| GLS-150 M (Bevel Gear Drive) | — | — |
| GLS-150, 200 M/Y (new turret version) | — | — |
| GLS-1500, 2000 M/LY/LMS/LYS | — | — |
| GLS-2800, 3000, 3300 M/Y/MS/YS | — | — |
| GMS-2000 ST (15 station turret) | — | — |
| GMT-2000 | — | — |
| GS-200, 260, 280 M/MS | — | — |
| GS-400, 600, 6000, 6600, 8000, 8800 M | — | — |
| GS-400 M (old turret version) | — | — |
| GS-2000 - 4000 M/Y/MS/YS (12 station turret) | — | — |
| GS-2000 - 3300 M/Y/MS/YS (16 station turret) | — | — |
| GS-3000, 3300, 3600 alpha | — | — |
| GS-4000, 4300 L | — | — |
| GS-6000 | — | — |
| GTH-2000, 2600 M | — | — |
| GTS-150 M (Bevel Gear Drive) | — | — |
| GTS-150 MMX/XY (new turret version) | — | — |
| GTS-200, 260 MMX/XY (new turret version) | — | — |
| GTW-1500 | — | — |
| GTX/GTZ-2000, 2600 M/Y (12 station turret) | — | — |
| GTX/GTZ-2000, 2600 M/Y (16 station turret) | — | — |
| GTZ-1500Y | — | — |
| GV-500, 780 M | — | — |
| GV-800, 1000 M | — | — |
| SK-38 | — | — |
| SW-12 | — | — |
| SW-20 | — | — |
| SW-20II | — | — |
| SW-32, SW-32II | — | — |
| SW-42 | — | — |
| TS-100 M | — | — |
| WE-1500, 2000 /L/LY | — | — |
All machine builders for 0° multi-axis driven toolholders →
The machine model alone does not decide the holder. The same model can leave the factory with different turrets — station count, model suffix and key arrangement all change the mounting. Tell us the machine, the turret and the operation and we confirm the mounting before quoting.
Already using another brand? Send the drawing or the article number of the holder you run today and Mongtec will convert it to an equivalent Mongtec holder — same mounting, same reach, same output.