Double 90° holders carry two right-angle outputs from one turret station, so two cross features are cut without indexing the turret between them. Mongtec Precision, a Taiwanese tooling brand headquartered in Taichung, Taiwan, supplies them to mount on Goodway turrets.
35 Goodway models. Where the turret interface is published it is shown; where it is blank the interface depends on the turret actually fitted and is confirmed at enquiry.
| Machine model | Turret interface (where published) | Turret |
|---|---|---|
| GA-2000-3600 M | — | — |
| GA-3000, 3300, 3600 | — | — |
| GLA-1500 M | — | — |
| GLS-150 M (Bevel Gear Drive) | — | — |
| GLS-150, 200 M/Y (new turret version) | — | — |
| GLS-1500, 2000 M/LY/LMS/LYS | — | — |
| GLS-2800, 3000, 3300 M/Y/MS/YS | — | — |
| GMS-2000 ST (15 station turret) | — | — |
| GMT-2000 | — | — |
| GS-200, 260, 280 M/MS | — | — |
| GS-400, 600, 6000, 6600, 8000, 8800 M | — | — |
| GS-400 M (old turret version) | — | — |
| GS-2000 - 4000 M/Y/MS/YS (12 station turret) | — | — |
| GS-2000 - 3300 M/Y/MS/YS (16 station turret) | — | — |
| GS-3000, 3300, 3600 alpha | — | — |
| GS-4000, 4300 L | — | — |
| GS-6000 | — | — |
| GTH-2000, 2600 M | — | — |
| GTS-150 M (Bevel Gear Drive) | — | — |
| GTS-150 MMX/XY (new turret version) | — | — |
| GTS-200, 260 MMX/XY (new turret version) | — | — |
| GTW-1500 | — | — |
| GTX/GTZ-2000, 2600 M/Y (12 station turret) | — | — |
| GTX/GTZ-2000, 2600 M/Y (16 station turret) | — | — |
| GTZ-1500Y | — | — |
| GV-500, 780 M | — | — |
| GV-800, 1000 M | — | — |
| SK-38 | — | — |
| SW-12 | — | — |
| SW-20 | — | — |
| SW-20II | — | — |
| SW-32, SW-32II | — | — |
| SW-42 | — | — |
| TS-100 M | — | — |
| WE-1500, 2000 /L/LY | — | — |
All machine builders for double 90° driven tools →
The machine model alone does not decide the holder. The same model can leave the factory with different turrets — station count, model suffix and key arrangement all change the mounting. Tell us the machine, the turret and the operation and we confirm the mounting before quoting.
Already using another brand? Send the drawing or the article number of the holder you run today and Mongtec will convert it to an equivalent Mongtec holder — same mounting, same reach, same output.
Mongtec publishes twin-output 90° driven tool holders for 34 Goodway machine models. On these machines the holder is used for two cross-drilling or cross-tapping operations from a single turret station, so the job needs fewer stations. Article numbers are matched to the machine at RFQ — we confirm the turret interface from the builder’s drawing rather than assume it from the model name.
Goodway machine not on this list? Send the model and we confirm the interface →