The DMG MORI NTX 2000–3000 2nd Gen (BMT60) is listed under BMT40 in Mongtec’s TOOL HOLDER SELECTION GUIDE; published machine data also reports BMT60, so the fitted turret depends on the build. Mongtec Precision, a Taiwanese tooling brand headquartered in Taichung, Taiwan, supplies driven tool holders and static tooling on the open machine-side BMT and VDI (DIN 69880) standards used by this machine class. The exact Mongtec model for your machine configuration is confirmed by Mongtec engineering at RFQ.
| Machine brand | DMG MORI |
|---|---|
| Model | NTX 2000–3000 2nd Gen (BMT60) |
| Turret interface | Mongtec's TOOL HOLDER SELECTION GUIDE lists the DMG MORI NTX 2000–3000 2nd Gen (BMT60) under BMT40. Published machine data also reports BMT60; the fitted turret depends on the build. Send a photo of the turret face and Mongtec confirms the fit before quoting. |
| Driven tool line speed | 6,000–12,000 rpm standard (up to 32,000 rpm with speed increaser) |
| Max torque | Up to 160 Nm (line capability; unit rating confirmed at RFQ) |
| Coolant | Internal / external, up to 100 bar |
| Runout | ≤0.003 mm (0° axial driven line) |
DMG MORI turret rule: NL / NLX 1500–3000 use BMT60 on 12-station turrets and BMT40 on 20-station turrets; NLX 4000 and NT 4000–5400 use BMT60; Duraturn, NT/NTX 1000–3200, NRX 2000, NZ and NZX use BMT40. Trifix VDI turrets (VDI25/30/40 Trifix) accept standard VDI holders. The same model can be built with a different turret, so this is a general rule, not a confirmed interface for your machine — email the machine model and a photo of the turret face; the interface is confirmed in Mongtec's formal quotation.
TOOL HOLDER SELECTION GUIDE Ver 2026.08 (PDF, 2.6 MB)
Models listed in this catalogue section: DURATURN 2050, 2550 (MC) / NL, NLX 1500, 2000, 2500 20 STATION TURRET / NT, NTX 1000, 2000 / NT 3000,3100,3150,3200 / NRX 2000 / NZ 1500, 2000 16 STATION TURRET / NZX 1500, 2000 20 STATION TURRET
| Article no. | Tool clamping | What it does on the machine |
|---|---|---|
| M56084 | 25 | 180° reversible — Facing & face grooving |
| M74484 | 20 | 180° reversible — Facing & face grooving |
| M35184 | Ø32 | 180° reversible — Boring, U-drilling & ID grooving |
| M85285 | Ø40 | 180° reversible — Boring, U-drilling & ID grooving |
| M14184 | Ø40 | 180° reversible — Boring, U-drilling & ID grooving |
| M86084 | Ø25 | 180° reversible — Boring, U-drilling & ID grooving |
| M73884 | Ø32 | 180° reversible — Boring, U-drilling & ID grooving |
| M83884 | Ø40 | 180° reversible — Boring, U-drilling & ID grooving |
| M93184 | Ø25 | 180° reversible — Boring, U-drilling & ID grooving |
| M83184 | 20 | 180° reversible — OD turning, threading, parting & grooving |
| M90284 | 20 | 180° reversible — OD turning, threading, parting & grooving |
| M01284 | 20 | 180° reversible — OD turning, threading, parting & grooving |
| M40284 | 25 | 180° reversible — OD turning, threading, parting & grooving |
| M45184 | 25 | 180° reversible — OD turning, threading, parting & grooving |
| M26084 | 25 | 180° reversible — OD turning, threading, parting & grooving |
| M36084 | 25 | 180° reversible — OD turning, threading, parting & grooving |
| M46084 | 20 | OD turning, threading, parting & grooving |
| M44188 | 25 | OD turning, threading, parting & grooving |
| M4057 | ER32 | Axial (0°) drilling & milling |
| M6057 | ER32 | 180° reversible — Radial (90°) face drilling & milling |
Article numbers shown as links have a specification page with the catalogue drawing. The rest are published in the Mongtec selection guide; Mongtec confirms the final article number against your turret drawing at RFQ.
Article numbers with a specification page on this site: M1257
Mongtec also supplies BMT40, BMT60, BMT68 and BMT80 holders and builder-specific interfaces (Mazak, Nakamura-Tome, Haas BOT, Okuma BOT, Muratec BOT) — the 228 article numbers published here are a subset of the range. Mongtec tooling is exported to five continents and supplied to machine-tool builders. Lead time is confirmed per item and quantity at quotation.
Request a quote for this machine
| Article no. | Type | Collet / coupling | Ratio | Max speed | Torque |
|---|---|---|---|---|---|
| M4176 | Axial Tool Holder | — | 1:1 | 6000 rpm | 32 Nm |
Listed from the Mongtec Tool Holders — VDI & BMT, Ver 2026.3 catalogue for the BMT60 turret interface. This is the published range for that interface size, not a confirmed fit for this specific machine configuration — Mongtec engineering verifies interface dimensions, clearance and drive coupling per machine at RFQ. Ask engineering to confirm →
Representative photographs of Mongtec driven and static turret tooling in the BMT60 class. These are production units from the Mongtec range, not renderings — but they are shown as examples of the BMT60 product family, not as the confirmed article number for this machine. Mongtec engineering verifies the interface, clearance and correct article code for your specific machine at RFQ.
Builds sold under the DMG MORI NTX 2000–3000 2nd Gen (BMT60) name do not all carry the same turret, and the turret decides which Mongtec tool holder fits.
Check the turret face against the interfaces shown on this page:
| Interface | What to check on the turret |
|---|---|
| BMT60 | Centre bore ø60 mm (the BMT number is the bore diameter). Machine-builder specific size: measure the bolt spacing as well. |
| BMT40 | Centre bore ø40 mm (the BMT number is the bore diameter). Machine-builder specific size: measure the bolt spacing as well. |
Count the turret stations, photograph the turret face and the machine serial plate, and email them with the model name. The interface for your machine is confirmed in Mongtec's formal quotation.
Mongtec supplies BMT and VDI (DIN 69880) driven tool holders and static tooling compatible with the DMG MORI turret platform. Interface: BMT40 (Mongtec catalogue); BMT60 also reported. The exact configuration is confirmed by Mongtec engineering at RFQ.
Yes. BMT and VDI are open machine-side standards, so switching supplier does not require any turret modification. Mongtec also publishes cross-reference pages for WTO, Heimatec, EWS, Eppinger, BIG and other brands.
Lead time is quoted per order and ships from Taichung, Taiwan.
Yes — Mongtec supplies driven and static tool holders for this turret. BMT60 is not in the article-number range published on this site, but it is a range Mongtec supplies and ships regularly for DMG MORI machines.
Turret coverage: DMG MORI NL / NLX 1500, 2000, 2500, 3000 (12-station) · NLX 4000 (12-station) · NT 4000, 4200, 4250, 4300, 5000, 5400 · NZL 2000, 250 · NZX 2500 (12-station).
Station count matters here: the same NL / NLX model can carry a BMT40 or a BMT60 turret depending on configuration, which is why the turret — not the model name — decides the holder.
Mongtec driven and static tool holders are exported worldwide across five continents, and are supplied to machine tool manufacturers as well as to end users. Lead time is confirmed against the items and quantity you need.
To quote we need: the machine model and turret designation, the station count, a turret interface drawing or a clear photo of the turret face, the holder orientation (axial or radial) and the clamping or collet size you need, and the quantity. A drawing of the holder you are replacing works just as well.
Email info@mongtec.com to discuss your application and request drawings, or send an enquiry here. Mongtec engineering will confirm the fit against your turret before anything is quoted.
All 228 article numbers with full specification · How to choose a driven tool holder · PSC / ISO 26623 tooling
Machine builders regularly ship the same model with different turrets — station count, model suffix and the number of keys all change the mounting. The Hardinge Conquest H51 is BMT55 in the 12-station build and BMT45 in the 16-station build; the Okuma GENOS L300 M is VDI40, while the L300 MW/MYW uses a 65×73 mm bolt pattern. This is the single most common reason a driven tool holder arrives and will not bolt on. BMT bolt pattern reference — 38 patterns by machine builder →
Send your model and a photo of the turret face — we confirm the fit before quoting →
Whether a holder mounts is decided by the turret bolt pattern and the drive coupling, not by the machine name alone. The types below are published by Mongtec for this interface; the exact article number is confirmed against the actual turret drawing at RFQ.
BMT60 article numbers · BMT bolt pattern reference (38 patterns) · All driven tool types and turret interfaces